[Msg]
M0=This is Register B. Starting Address Formation Error.
M1=Starting Address Formation Error.
M2=Please choose an Node on the Diagram.
M3=There is no Reading Block could be added.
M4=It couldn't add a read block from itself.
M5=The Block is already exist.
M6=Node has reached the maximum number of limit.
M7=Node Numebr setting error.
M8=The same data without uploading.
M9=PLC Type setting error.
M10=Upload completed.
M11=EtherLink Table Error. There are two identical node number blocks:
M12=The same data without downloading.
M13=Stop data exchange fail.
M14=Download completed. (EtherLink originally stopped. PLC originally run, the user give up starting it again.)
M15=Download completed. (EtherLink and PLC originally stopped.)
M16=Download completed. (EtherLink restarted complete. PLC originally run, the user give up starting it again.)
M17=Download completed. (EtherLink restarted complete. PLC originally stop.)
M18=Download completed. (PLC restarted complete.)
M19=Timeout., IP Address error?
M20=Timeout. Protocol setting error?
M21=Timeout. The connection has been established, the command sent no response. Station Address setting error?
M22=Timeout. The connection has been established, the command sent no response.
M23=The block size couldn't be over
M24=The block size couldn't  be less than 1.
M25=The range is over the upper limit of register B.
M26=The range is over the upper limit.
M27=ComPort Number isn't yet set.
M28=Station Address isn't yet set.
M29=Station Address setting is correct.
M30=AH500 is not supported EtherLink function.
M31=The number of blocks is over the upper limit.
M32=The number of blocks is qualified.
M33=Network cable isn't plugged in. Start the EtherLink fail.
M34=IP address and Ethernet Station Address settings error.
M35=IP address setting error.
M36=Ethernet Station Address setting error.
M37=There are blocks asking data from itself.
M38=Start
M39=Stop
M40=Successed
M41=Failed
M42=(Network cable is not plugged in).
M43=All IP Address are filled.
M44=Ethernet station address is not set.
M45=Ethernet station address overlap.
M46=exist overlapping blocks of data received.
M47=All  settings of received blocks are correct.
M48=IP Range error.
M49=Data exchange block size doesn't be larger than 1980.
M50=Data exchange block size doesn't be less than 1.
M51=Error! It will cross blocks of register B.
M52=Address is out of register range.
M53=The port is occupied.
M54=The address overstep the scope of this block.
M55=The value exceed the limit.
M56=Input error.
M57=Do you want to keep these Ether Link settings?
M58=Confirmation
M59=Removing the node will delete all related data exchange blocks. Are you sure?
M60=Warning
M61=Do you want to overwrite this file?
M62=Download completed. PLC originally started, restart it?
M63=EtherLink is running. Do you want to stop it and overwrite the  EtherLink Table in PLC?
M64=PLC is running. Do you want to stop it and restart it after downloading?
M65=Do you want to upload an overwrite current Ether Link settings.
M66=Are you sure you want to exit this Wizard?
M67=Are you sure you want to close this window?
M68=Printer has not been installed yet.
M69= data isn't synchronized. Do you want to upload or downlaod?
M70= IP address aren't yet filled.
M71=Data is the same.
M72=File error.
M73=IP Address is not set.
M74=IP Address overlap.
M75=IP Address setting is correct.
M76=Users canceled uploading or downloading data synchronization.
M77=Strat Ether Link successed.
M78=Stop Ether Link successed.
M79=Start Ether Link failed.
M80=Stop Ether Link failed.
M81=Start Ether Link fialed(Network cable is not plugged in).
M82=Stop Ether Link fialed(Network cable is not plugged in).
M83=Starting Address is out of range.
M84=Ending Address is out of range.
M85=It couldn't add the block in asynchronous node.
M86=This register is full.
M87=Synchronous nodes couldn't be deleted.
M88='s table includs overlapping blocks.
M89=Table is correct.
M90=It exists asynchronous node, please delete that firstly.
M91=It couldn't communicate with asynchronous node.
M92=Ether Link data is asynchronous. Do you want to download and monitor?
M93=All nodes
M94=Online (Connect to an Single Node)
M95=Offline (Disconnect from an Single Node)
M96=There are asynchronous nodes with NWCONFIG:
M97=Register
M98=Blocks overlap.
M99=The number of sending and receiving blocks is out of range :
M100=All setting is correct.
M101=Finish
M102=Address range
M103=Size
M104=EtherLink Table is the same (C).
M105=EtherLink Table is the same (C).
M106=EtherLink Table is the same.
M107=EtherLink Table is the same.
M108=Message
M109=It gave up synchronizing Ether Link table.
M110=Error
M111=The number of blocks is out of range. Please download Ether Link table of this nodes in all Networks, again.
M112=Downloading Finished.
M113=Uploading Finished.
M114=The connected PLC name is different. Users stopped communicating.
M115=The name of PLC is different between connected PLC and currect settings. Do you still continue to communicate?
M116=Yes
M117=Yes to all
M118=No
M119=No to all
M120=Cancel
M121=Network
M122=Offline
M123=Online
M124=Communication Error.
M125=Node
M126=The address out of receiving block range.
M127=The address out of sending block range.
M128=Signed Decimal
M129=Unsigned Decimal
M130=Hexadecimal
M131=Binary
M132=Ascii
M133=The number of data exchange blocks is out of range. It couludn't be added more.
M134=The file exists, overwrite?
M135=Data can't exchange with self-Node.