[Msg]
M0=Input Error!
M1=Communication port has been used or this port doesn't exist!
M2=The COM connected with Modem!
M3=Communication error (function does not support)
M4=Time Out!
M5=Failed to communicate!
M6=Warning
M7=Confirm
M8=Connect again?
M9=Setting OK!
M10=Fail to input the linking times!
M11=Do you want to read the configuration setting from the connected PLC?
M12=Are you sure to overwrite this file?
M13=The PLC Link setting has been changed, do you want to keep it?
M14=Start address error!
M15=Data length error!
M16=Reading data length error!
M17=Writing data length error!
M18=Please disable the monitor mode first!
M19=Failed to set the running times!
M20=The value is out of range!
M21=Device Name
M22=Value
M23=Device Comment
M24=ID
M25=Station Addr.
M26=R/W
M27=Master Device Data
M28=<=>
M29=Slave Device Data
M30=Length
M31=Status
M32=Enabled
M33=Disabled
M34=R
M35=W
M36=Continue to Monitor
M37=Stop Monitor
M38=Execute Times
M39=The total device quantity is over this model in the Master Read Setting!
M40=The total device quantity is over this model in the Master Write Setting!
M41=The total device quantity is over this model in the Slave Read Setting!
M42=The total device quantity is over this model in the Slave Write Setting!
M43=Binary Mode
M44=Hide Binary Mode
M45=Are you sure to initialize the data?
M46=Auto Mode
M47=Manual Mode
M48=User Setting
M49=PLC Link Run
M50=Device Type
M51=The station address is out of range.
M52=Unknown device coundln't be enable.
M53=The station address in NWCONFIG should be
M54=It couldn't be L register.
M55=The register should be D or M at the same time.
M56=The DVP-series couldn't be the Slave device in 450-words Transfer Capacity mode.
M57=The register of Master and Slave device must be the same.
M58=The slave device couldn't be enable in 450-words mode.
M59=Master device couldn't use L register in this mode.
M60=The Master device doesn't support 450-words mode.
M61=Master device should be D register.
M62=Slave device should be D register.
M63=Write block size couldn't greater than
M64=Read block size couldn't greater than
M65=Master device writing address is out of range.
M66=Master device reading address is out of range.
M67=In 100-words mode, the max address of D register is 32767.
M68=Unknown register of slave writing block.
M69=Unknown register of slave reading block.
M70=The writing block address of Slave device is out of range.
M71=The reading block address of Slave device is out of range.
M72=The writing block register of Slave device is only could be D or M.
M73=The reading block register of Slave device is only could be D or M.
M74=The station address of Master device must be greater than 0.
M75=Master device type couldn't be User Defined or Unknown.
M76=When the station address is 0, it couldn't be enable.
M77=Station address
M78=doesn't exist in this Network.
M79=Device type is error.
M80=Communication error.
M81=Unknown device type, please check ini-file:
M82=Device type error, please check the connected device is correct.
M83=Notice that the master port in this PLC is different to the plan of software. When you download this table, the setting would be modified.
M84=The PLC name is different to the device name of Network Configuraion. Do you still continue to communicate?
M85=The connected device counldn't support routing function.
M86=In NWCONFIG plan, it couldn't find the device with ports connecting Network number is:
M87=disconnected,
M88=disconnected
M89=, and the node number is 
M90=device
M91=Do you want to communicate without routing function?
M92=All item should be set.
M93=lost
M94=Time out
M95=All setting of PLC Link is correct.
M96=Device address couldn't be empty.
M97=Please select the register.
M98=Please select device type.
M99=If you changed the Master device, the all PLC Link setting would be reset. Are you sure to change that?
M100=Warining
M101=According to the network architecture planned by NWCONFIG, the communication control of the network will be lost (including the master device) if the PLC link starts. Will the PLC Link start?
M102=Address error
M103=Do you want to save and exit?
M104=Finish
M105=32 links Enabled
M106=Synchronic R/W
M107=address is out of range.
M108=read
M109=write
M110=Master Device 
M111=Slave Device
M112=Network
M113=There isn't a Ethernet port in Master device, please change the communication settings.
M114=Please set the IP address of Master Device firstly.
M115=Data exchange times must be between 1 and 65535.
M116=PLC Run
M117=Communication Error.
M118=When synchronic R/W function starts, only register D could be used.
M119=There were some error blocks already disabled.
M120=and
M121=master read address overlap.
M122=slave write address overlap.
M123=The number of Time Out can't be greater than
M124=The number of Interval Time can't be greater than
M125=$$$$$ read coil size can't be greater than $$$$$ words.
M126=$$$$$ write coil size can't be greater than $$$$$ words.
M127=The first station of Routing Mode isn't connected to the Master device. Please change the driver or Master device.
M128=The routing settings of connected device is different from current network plan.
M129=The file exists, overwrite?
M130=The communication adopts the packet routing mode now. If the PLC link function of this master is enabled, the master is disconnected. Do you still want to enable the function?
M131=The station number must be continued in 16-words mode. Modifying station number of this block would change station number of each block. Still Modify?
M132=The station number must be continued in 16-words mode. The station number could less than $$$$$ in this blocks.
M133=Unknown
M134=Master Port:
M135=Rack
M136=Slot
M137=The PLC Link Master port can't be a slave port.
M138=Please enter station number.
M139=Changing to 16 words mode will clear the last 16 blocks data. Are you sure to modify?
M140=In 16-word mode, station address must be continue. The station address of this block can't be greater than $$$$$.
M141=Addr.
M142=Delayed Time
M143=Delayed Time can't be empty
M144=Delayed time can't be greater than 
M145=Please choose slave register type

